B-481 Stainerbondz™

    B-481 Stainerbondz™ DESCRIPCIÓNTecnología de impresión: transferencia térmicaTipo de material: poliésterAcabado: blanco mateAdhesivo: acrílico permanente APLICACIONESEtiquetado de portaobjetos y otro material de laboratorio RIBBONS (Cintas de transferencia térmica)Serie R6400 CERTIFICACIONESCumple con RoHS de 2005/618/EC MCV, revisión de RoHS Directive 2002/95/EC CARACTERÍSTICAS ESPECIALESB-481 está especialmente diseñado para (en conjunto con el ribbon R-6400) el etiquetado de portaobjetos antes del proceso de tinción, dónde se requiere una especial resistencia química. B-481 es perfecto para los procesos comunes de tinción con Hematoxilina y Eosina.  DETALLES:   PHYSICAL PROPERTIES TEST METHODS AVERAGE RESULTS  Thickness ASTM D 1000 -Total (excluding liner) 0.0838 mm Adhesion to:     -Glass     -Polypropylene     -Stainless steel   20 minute dwell 24 hour dwell  20 minute dwell 24 hour dwell  20 minute dwell 24 hour dwell 74 oz/inch (81.4 N/100mm) 77 oz/inch (84.7 N/100mm) 73 oz/inch (80.3 N/100mm) 77 oz/inch (84.7 N/100mm)  76 oz/inch (83.6 N/100mm) 78 oz/inch (85.8 N/100mm)  Tack ASTM D 2979 PolykenTM Probe Tack1 second dwell 1060 grams  Tensile strength and Elongation ASTM D 1000 -Machine direction 40 lbs/inch (704 N/100mm), 75%         PERFORMANCE PROPERTIES-ENVIRONMENTAL RESISTANCE B-481 samples were printed with the R6400 Series ribbon on Bradyprinter THT Model 300X-Plus thermal transfer printer.  Printed samples were laminated to glass microscope slides and then exposed to the indicated environmental conditions.   PERFORMANCE PROPERTIES TEST METHODS EFFECT TO LABEL EFFECT TO PRINT IMAGE High Service Temperature 30 days at 266°F (130°C) Slight yellowing at 130°C, moderate yellowing at 145°C No visible effect Low Service Temperature 30 days at -112°F (-80°C) No visible effect No visible effect Humidity Resistance* 30 days at  100°F (37°C), 80% relative humidity No visible effect No visible effect Sterilizer resistance (autoclave resistance) Ramp time 28-30 minutes, peak temperature 125°C , peak pressure 21psi and peak duration 5 minutes, Sterilemax Table Top Steam Sterilizer, Series 1277 No visible effect if slides were placed on the rack flat. Slight water mark at the bottom edge if slides were placed on the rack vertically No visible effect Abrasion Resistance Taber Abraser, CS-10 grinding wheels, 500 g/arm, 150 cycles No visible effect Print still legible after 150 cycles   *B-481 no se recomienda para su uso con temperaturas superiores a 35ºC y humedad relativa superior a 80%.    PERFORMANCE PROPERTIES-CHEMICAL RESISTANCE  B-481 samples were printed with R6400 Series ribbon on BradyprinterTM THT Model 300X-Plus thermal transfer printer. Printed samples were laminated to aluminum panels and allowed to dwell 24 hours prior to testing. Testing consisted of 5 cycles of 10 minute immersions in the specified chemical followed by 30 minute recovery peroids. After the final immersion the printed image was rubbed 10 times with a cotton swab saturated with the test fluid. Testing was conducted at room temperature.     CHEMICAL REAGENT EFFECT TO PRINT/TOPCOAT WITHOUT RUB EFFECT TO PRINT/TOPCOAT WITH RUB EFFECT TO ADHESIVE  Acetone 1 1 1  Ethanol 1 1 1  Toluene 1 1 2  Isopropanol 1 1 1  Xylene 1 1 2  MEK 1 1 1  Deionized Water 1 1 1  Dimethylsulfoxide (DMSO) 1 1 1  3% Alconox® Detergent 1 1 1  50% Acetic Acid 1 1 1  10% Sulfuric Acid 1 1 1  10% Clorox® Bleach Solution 1 1 1  10% Sodium Hydroxide 5, topcoat delamination 5 1  Rating scale:    1=no visible effect   2=slight smear or print removal or adhesive oozing, detectable but minimal   3=moderate smear or print removal or adhesive oozing   4=severe smear or print removal or adhesive oozing   5=complete smear, print removal or topcoat removal (delamination) or adhesive oozing     PERFORMANCE PROPERTIES-Slide Staining Test  Samples of B-481 printed with R6400 Series ribbon were laminated to glass microscope slides.  These slides were placed in the Leica AutoStainer XL automated slide stainer.   The slides were processed using the H&E (hematoxilin and eosin) staining process.  Labels were adhered to the following brands of slides:   Cole-Parmer® - precleaned frosted, precleaned Superfrost® and plain precleaned Superfrost®   Fisher Scientific – precleaned frosted beveled   Erie Scientific - precleaned Superfrost® plus   Mercedes Medical - (precleaned, belveled edge, double frost)   Gold Seal Products® - Gold Seal® precleaned   REAGENT STATION STEP DURATION (minutes)  None Oven 1 10:00  Xylene 1 2 2:00  Xylene 2 3 2:00  100% denatured ethanol 3 4 2:00  100% denatured ethanol 4 5 2:00  70% denatured ethanol 5 6 1:00  Wash (tap water) Wash 1 7 2:00  Hematoxilin stain (Harris formula modified, supplied by Ricca Chemical Company) 6 8 5:00  Wash (tap water) Wash 2 9 2:00  Acid Alcohol (mixture of 1.25% of concentrated HCl, 69.26% of ethanol and 29.49% of DI H2O) 7 10 0.02  Wash (tap water) Wash 3 11 3:00  Scott’s bluing reagent (supplied by Fisher Scientific) 8 12 3:00  Wash (tap water) Wash 4 13 3:00  Eosin Y stain (Stock formula, 1% alcoholic solution supplied by  Ricca Chemical Company) 14 14 2:00  95% denatured ethanol 15 15 0:30  100% denatured ethanol 16 16 2:00  100% denatured ethanol 17 17 2:00  100% denatured ethanol 18 18 2:00  Xylene Exit 19 30:00   Resultados del ensayo: después de la tinción todas las etiquetas permanecieron adheridas a todos los tipos de portaobjetos.  La impresión no se vio afectada. En algunos casos la superficie de la etiqueta quedó ligeramente rosada después del proceso.Los portaobjetos procesados y etiquetados con B-481 deben ser almacenados a una temperatura inferior a  27 ° C y una humedad relativa de 60%.